Termékek pvc gyanta gyártó (38)

Nuancier HELIOS pour tous nos produits en PVC : - fenêtres; - portes d’entrée ; - portes coulissantes

This product, which is the 3D figure of a lovely mushroom, is produced using EPDM rubber material, taking into consideration child safety regulations. You can use this product to strengthen the concept of natural playground in parks built with Robiwood products. Alternatively, you can choose this product for shopping malls, public parks, theme parks and other indoor/outdoor playgrounds. AGE GROUP:3+ yrs CRITICAL FALL HEIGHT:0.80 mt PLAY CAPACITY :2-4 child DIMENSIONS (LxWxH):3.20 mt x 1.70 mt x 0.80 mt

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Resin Rapid UV Curing 3D prototype 3D print out Number:GP1001 Material:Resin Rapid UV

Together with the Fachhochschule Münster – University of Applied Sciences we are working on ALWA PERM (patent No. 2583995). This is a metal-filled casting resin for producing a porous, resin-bound mould. These materials are applicable in the areas of thermoforming, the ceramic industry, intake moulds and devices, pneumatic cushioning, the filter industry, etc. ALWA PERM allows a castable production of porous metallic materials with a binder for the first time. The system offers a highly accurate mould surface reproduction. The profile characteristics goes far beyond the current state of the art. NO MORE DRILLING OF VACUUM HOLES! NO DAMAGE OF THE MOULD SURFACE DUE TO DRILLING HOLES

COMPOSITION ET ASPECT Blanc & incolore. CARACTÉRISTIQUES TECHNIQUES • Temps de formation de peau : environ 10 minutes (23°C, 50 % HR) • Temps hors poussière : environ 20 minutes (23°C, 50 % HR) • Allongement à la rupture: 150 % • ÉPAISSEUR polymérisé : en 24 h (23°C, 50 % HR) 3 mm • Température d’application : + 5°C à + 40°C CONDITIONNEMENTS Cartouche de 310 ML. STOCKAGE 18 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. PRÉCAUTION D'EMPLOI Éviter le contact avec la peau. En cas de contact avec les yeux, laver immédiatement avec de l’eau et consulter un spécialiste. Conserver hors de portée des enfants. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, sains, dégraissés et dépoussiérés. Ne pas utiliser sur support basique (maçonnerie, béton, marbre...). APPLICATION Étant donné la diversité des supports sanitaires acryliques, un essai de convenance préalable est nécessaire. Lisser à l’eau savonneuse, serrer...

IRIS is an acrylic cement paint, for interior and exterior use based on acrylic resins. It is recommended for building surfaces such as concrete, plaster, bricks, etc. It has a highly whitening and covering effect and it is also protective against humidity, high temperature and heavy weather conditions.

Gomastit 407 is a sealant based purely on silicone for joints in the natural stone and parquet area, as well as for connections of various construction materials. Gomastit 407 is mouldresistant, as well as UV and weather resistant. This product is easy to process and ensures durable sealing. Gomastit 407 is mechanically resilient and can be walked on. Usage:Facades, Sanitary, Interior construction, Floor

Acryl by Sarközy ist eine überstreichbare Dichtmasse auf Basis von Acryldispersion. Ab einer Kartusche erhältlich! Acryl by Sarközy wird erfolgreich eingesetzt bei Fassaden, im Fensterbau, den Oberkante-Sockeln und Türzargen. Das Verfugen von Anschlussfugen zwischen Beton und Mauerwerk oder Decke und Wand sind die klassischen Anwendungen dieser Dichtmasse. Acryl by Sarközy Dichtstoff ist nahezu geruchlos und nicht korrosiv. Es ist witterungsbeständig, regenfest und bildet nach dem Einbringen durch Verdunsten von Wasser eine plastisch-elastische Masse. Grundstoff: Acryldispersion Kartuschenfüllmengen: 310ml Standardfarben: Weiß und Transparent

2H Acryl 150 mit Quarzsand ist ein elastoplastischer Dichtstoff auf Acryldispersionsbasis für innen und außen. Einkomponentiger Acrylatdichtstoff für den Innen- und Außenbereich mit einer max. Bewegungsaufnahme von 10%. Putzähnliche Oberfläche zum Verschließen von Rissen in Putz und Mauerwerksflächen innen und außen. Verpackung in 310ml Kartusche.

Grazie ai nostri macchinari e al nostro personale specializzato siamo in grado di garantire un'ottima finitura in tempi molto brevi. Inoltre la lavorazione del Pvc, ci permette di soddisfare le esigenze dei clienti che desiderano un materiale economico. Con la lavorazione del PVC si ottengono tolleranze molto simili ai materiali più tenaci, come il Delrin e il Nylon, +/-0,2 mm su parti fresate e H7 su parti tornite.

Référence COLLEFIBRE-5KG

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

RTV2 Silikonkautschuk (Platin Katalysator) mit Shorehärte 13 ShA für den Einsatz im Orthopädie, Formenbau, Modellbau, SPFX, Abformung, Dichtungstechnik. Für den direkten Kontakt mit der Haut geeignet.

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

REFERENCE : ZA22TB/1 Elasto. polyadition - 22Sh.A - SFC ZA22 THIXO BODY 1+1 kg DESCRIPTION : Silicones Bi-Composants 22 Shore A. Système résistant à la traction, au déchirement et aux produits chimiques. Idéal pour moules. APPLICATION : Confection d'effets spéciaux, Prise d'empreinte rapide direc tement à la main. Moule du corps humain. RATIO : 100/100 DURETE SHORE : A 22 TEMPS DE TRAVAIL : 9 MIN UNITE DE VENTE : KIT MINIMUM DE COMMANDE : KIT DE 2KG

Magnifique statue design CHIEN en résine pour rendre unique votre intérieur. - Détails du produit : Statue sculpture décorative design CHIEN FUNNY en résine H152 cm (Multicolore) - Cette statue sculpture est entièrement en résine et finition brillante - Style design et contemporain / Couleur : multicolore - Hauteur : 152 cm / Longueur : 130 cm - Outdoor / Indoor - Finitions peintes à la main Produit NEUF - Garantie 1 an - Commande préparée avec soin et livraison rapide, avec suivi colis (expédié généralement sous 48 à 72 heures). - Livraison au rez de chaussée. Pas de livraison ni en Corse, ni dans les îles.

POLYMIX VULKAZE TERMOPLASTİK ELASTOMER – TPV/OXEFLEX Vulkaze termoplastik elastomerler (TPVS), geleneksel termoset kauçukların fonksiyonel özelliklerine sahiptir, ancak termoplastik üretim ekipmanlarında işlenebilir.

Acrylic copolymer is an emulsion-based, matt-looking, economical inner surface topcoat paint. It has dull and smooth appearance. It adheres perfectly to surfaces and does not cause any swelling or flaking. It has high breathing capacity.

Suitable for universally usable refurbishment wax for mending surface damages and small defects in varnished, oiled or glazed wood surfaces indoors, such as doors and furniture, wall panels and wood parts.

Professionelle Reinigungs- und Pflegeprodukte für Schutzwände Bei uns erhalten Sie Spezialprodukte für die richtige Reinigung und Pflege von Acrylglas und anderen transparenten Kunststoffen Antistatischer Kunststoff-Reiniger und Pfleger Messbar antistatisch und pflegend, erzeugt keine Spannungsrisskorrosionen VPE: Sprühflasche á 250 ml (24 St./Karton) oder 500 ml (12 St./Karton) oder im 10-l-Kanister Kunststoff-Intensivreiniger Intensiv reinigendes Spezialmittel zur Beseitigung stärkerer Verschmutzungen. VPE: Sprühflasche á 250 ml Spezial-Tücher für die Kunststoffpflege Fusselfrei, besonders weich und saugfähig. Baumwollmaterial strapazierfähig und waschbar (bis 40 °C), Größe ca. 28 x 24 cm, Stofffarbe: Chamois VPE: 60 Stück/Packung Acrylglas-Polierpaste Zur Entfernung von Kratzern und blinden Stellen. VPE: Tube á 75 ml (92 g) oder á 200 ml (245 g) Tipps zur richtigen Reinigung/Pflege von Acrylglas finden Sie auf unserer Website.

Setzt man dem Kieselgel einen Indikator zu, kann man anhand eines Farbumschlages die Wasseraufnahme des Produktes kontrollieren. So wechselt beispielsweise bei einem Orangegel die Farbe mit zunehmender Wasseraufnahme von Orange zu einem leichten Schwarz-Grün. Somit erkennt man sehr leicht, ob das eingesetzte Kieselgel verbraucht ist und durch neues ersetzt werden muss, beziehungsweise, ob das verbrauchte Kieselgel regeneriert werden muss. Kieselgel von Silcarbon arbeitet mit einem Farbindikator, welcher als Ersatz für das unter Krebsverdacht geratene Blaugel eingesetzt wird. Das heißt, dass bei Silcarbon definitiv kein Kobaltchlorid eingesetzt wird.

Starre- und flexible Dichtungsschlämme mit mineralisierenden Eigenschaften

1-K Montagekleber auf MS-Polymer-Basis. Eigenschaften: Spez. Gewicht 1,54 g/ml, anstrichverträglich, geruchs-neutral, Isocyanatfrei, MS-Polymer reagiert mit Luftfeuchtigkeit, zulässige Gesamtverformung +/- 25%, Aushärtung bei 23° C 2 mm/Tag, Hautbildungszeit ca. 10 Min., schnelle Anfangshaftung,breites Haftspektrum. Temperaturbeständigkeit:-40° bis +90° C. Verarbeitungstemperatur:+5° bis +40° C. Anwendung: Verkleben von Paneelen,Holzleisten, Fensterbänken, Baumaterialien, Metallverbindungen, Schiffbau usw. Temperaturbeständigkeit:-40° bis +90° C Verarbeitungstemperatur:+5° bis +40° C

Hochelastischer Silikon-Dichtstoff mit sehr guter Haftung auf nahezu allen bauüblichen Untergründen und Materialien Ideal für Anschluss- und Dehnungsfugen im Bau- und Montagebereich, z. B. an Balkonen, Terrassen und Fenstern (Metall-, Holz- oder Kunststoffrahmen) sowie für Abdichtungen zwischen Beton- und Fassadenbauteilen. Neutralvernetzend (Alkoxy) Sehr gute Haftung auf vielen Baumaterialien Dauerhaft elastisch Nicht korrosiv gegenüber Metallen Schnelle Hautbildung und Durchhärtung Geruchsarm UV- und witterungsbeständig Inhalt: 300 ml EN 15651-1: F-EXT-INT-CC EN 15651-2: G

Silicon nitride is one of the hardest ceramics but also one of the most resistant. Si3N4 is mainly used in severe environments which combine extreme temperatures with abrasive and/or corrosive medium. Silicon nitride can be of different grades : sintered, hot pressed or reaction bonded. Selection of materials Microcertec offers two high-purity Si3N4 grades that are particularly suited for hostile environments : sintered silicon nitride hot pressed silicon nitride Both Si3N4 materials are mainly designed to be used in thermal-mechanical or corrosion-resistance applications because they show an outstanding behaviour to resist to wear, thermal shocks and corrosion (liquids and gases). Moreover, these pure Si3N4 grades offer a low thermal expansion. Properties Sintered silicon nitride and HP Si3N4 have the following properties : low density excellent thermal shock resistance excellent wear resistance excellent corrosion resistance (liquids and gas) low coefficient of thermal...

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Wholesale hot Sale Japan anime figure Uzumaki Naruto Collection resin figurine Number：:GRCS10013 Material：:Resin/Polystone Type：:Collectible

Transparent wood preservative, effective against micro organisms, bacteria fungi and algue. It is proposed for the long-time protection of every type of wood. It does not create a film, thus, it does not crack, shell or create a scale. PACKAGE:0,75 LT, 2,5 LT

REFERENCE : RESMPP16095 (ex PP1609)36kg/m2. RESIFOAM BAYMER AL759 5kg...kg MOUSSE POLYURETHANE RESIFOAM. Mousse polyuréthane expansive rigide approprié pour le remplissage d'élements par coulée. Applications:isolation industrielle,remplissage, reserves de flotabilité etc... MELANGE: 100parts RESIFOAM + 100parts DESMODUR(en volume)